VCS教程
http://hobgoblinconsulting.com/hints/vxvm/vcs/
系统重启后,VCS状态为ADMIN_WAIT or STALE_ADMIN_WAIT
After a reboot, a node in a VERITAS Cluster Server (VCS) environment is in an ADMIN_WAIT state or in a STALE_ADMIN_WAIT state
Details:
Below are descriptions of the states that a Cluster Server node could end up in after a reboot as seen from the following command:
# hastatus
attempting to connect....connected
group resource system message
--------------- -------------------- --------------- --------------------
sptsunvcs3 STALE ADMIN WAIT: all system stale
sptsunvcs4 STALE ADMIN WAIT: all system stale
ADMIN_WAIT state:
If VCS is started on a system with a valid configuration file, and if other systems are in the ADMIN_WAIT state, the new system transitions to the ADMIN_WAIT state.
If VCS is started on a system with a stale configuration file, and if other systems are in the ADMIN_WAIT state, the new system transitions to the ADMIN_WAIT state.
STALE_ADMIN_WAIT state:
If VERITAS Cluster Server is started on a system with a stale configuration file, and if all other systems are in STALE_ADMIN_WAIT state, the system transitions to the STALE_ADMIN_WAIT state as shown below. A system stays in this state until another system with a valid configuration file is started, or when the command hasys -force is issued.
Resolution:
If all systems are in STALE_ADMIN_WAIT or ADMIN_WAIT, first validate the configuration file (/etc/VRTSvcs/conf/config/main.cf) on all systems in the cluster by running the 'hacf -verify .' command for syntax error check (ensure that this command is run in the directory containing the main.cf file), and reviewing its contents for proper resource and service group definitions.
Then enter the following command on the system with the correct configuration file to force start VCS.
Below are descriptions of the states that a Cluster Server node could end up in after a reboot as seen from the following command:
# hastatus
attempting to connect....connected
group resource system message
--------------- -------------------- --------------- --------------------
sptsunvcs3 STALE ADMIN WAIT: all system stale
sptsunvcs4 STALE ADMIN WAIT: all system stale
ADMIN_WAIT state:
If VCS is started on a system with a valid configuration file, and if other systems are in the ADMIN_WAIT state, the new system transitions to the ADMIN_WAIT state.
- INITING===>CURRENT_DISCOVER_WAIT===>ADMIN_WAIT
If VCS is started on a system with a stale configuration file, and if other systems are in the ADMIN_WAIT state, the new system transitions to the ADMIN_WAIT state.
- INITING===>STALE_DISCOVER_WAIT===>ADMIN_WAIT
STALE_ADMIN_WAIT state:
If VERITAS Cluster Server is started on a system with a stale configuration file, and if all other systems are in STALE_ADMIN_WAIT state, the system transitions to the STALE_ADMIN_WAIT state as shown below. A system stays in this state until another system with a valid configuration file is started, or when the command hasys -force is issued.
- INITING===>STALE_DISCOVER_WAIT===>STALE_ADMIN_WAIT
Resolution:
If all systems are in STALE_ADMIN_WAIT or ADMIN_WAIT, first validate the configuration file (/etc/VRTSvcs/conf/config/main.cf) on all systems in the cluster by running the 'hacf -verify .' command for syntax error check (ensure that this command is run in the directory containing the main.cf file), and reviewing its contents for proper resource and service group definitions.
Then enter the following command on the system with the correct configuration file to force start VCS.
- #
- system_name
- This will have the effect of starting Cluster Server on that node and starting Cluster Server running on all other nodes in the ADMIN_WAIT or STALE_ADMIN_WAIT state.
- One of the most common causes of a node being in one of these states is the existence of /etc/VRTSvcs/conf/config/.stale. This file is typically left behind if Cluster Server is stopped while the configuration is still open, i.e. someone has forgotten to save changes made to a running main.cf configuration. The .stale file is deleted automatically if changes are correctly saved and will therefore not force the relevant node into an ADMIN state when it next has to restart Cluster Server. As indicated earlier, the file can be safely removed if the main.cf file is known to be ok.
相关推荐
NULL 博文链接:https://changda-junge.iteye.com/blog/932611
VCS_Admin_6.0.1.pdf
VCS用户手册
VCS_Runtime DEMO
入门一文已经向大家介绍了DB2双机的基本原理和配置方法,本文将接续上文,继续介绍DB2的高级需求-大规模并行处理(Massively Parallel Processing, MPP)-环境下,用户如何利用VCS配置双机互备环境。
VCS_for_windows__VVR WINDOWS平台下SYMANTEC的双机VCS配置
README_VCS_Cluster_Manager_6.0.1_Linux
vcs介绍使用方法 介绍如何具体使用synopsys公司的软件
使用VCS_and_PLI2.0进行接口开发,采用VCS已经验证过,是VERILOG和C的接口文档,描述非常详细
在芯片开发时,需要用到vcs工具,就可以参考用户手册进行相应的参数设置
这是跟vcs installer配套的,安装vcs的软件,软件版本为v11.1,可以安装vcs 2016版本
自己搭建的基于转子磁链定向的异步电机间接矢量控制模型,采用带转矩内环的转速、磁链闭环控制。
IC设计验证 VCS实验源码+文档 ,vcs入门学习非常值得拥有。
本文档提供有关适用于 Linux 的 Veritas Cluster Server (VCS) 版本 6.0 的重要信 息。请在安装或升级 VCS 之前仔细阅读整个文档。 “版本说明”中的信息可取代 VCS 的产品文档中提供的信息。 本《Veritas Cluster ...
本压缩包包括两个pdf文档,分别是《vcs student guide.pdf》和《数字逻辑芯片DV环境搭建.pdf》
VCS下编译通过的PLI的实例,包括功能仿真,和可综合代码
RISC全部源码,包含仿真文件,使用makefile脚本编写,能通过vcs编译
vcs编译器常用命令介绍,使用与IC设计人员和验证人员,相对基础
vcs详细安装文档,很详细。
VCS VCS user guide VCS用户手册 VCS-userguide-Q-2020.03-SP2